- PASSIVE DI
The Radial JDI is a warm sounding passive direct box that can transfer extreme signal levels without distortion while eliminating hum and buzz caused by ground loops.PRODI
The Radial ProDI is a high performance passive direct box that is ideally suited for bass and acoustic guitar to deliver a warm, distortion-free sound.Trim-Two
The Radial Trim-Two is a passive direct box, designed for use with laptop computers and other consumer type devices where the user has a requirement for a 'ready access' volume control for quick adjustments on stage.JDI Stereo
The Radial JDI Stereo is a passive stereo direct box designed to handle extreme signal levels without distortion of any kind.PROD2
The Radial ProD2 is a high performance stereo direct box designed to easily interface keyboards to the PA and recording system without noise.StageBug SB-2
The Radial SB-2 is a passive direct box designed for keyboards and active bass. Features stereo to mono mix function to save mixer channels.JDI Duplex
The Radial JDI Duplex is a stereo passive direct box that fully capable of handling any audio signal without distortion, artefact or noise.ProAV1 & PROAV2
The Radial ProAV is a passive direct box with stereo-to-mono merge function designed specifically for the audio-video integrator to reduce channel requirements.StageBug SB-5
The Radial StageBug SB-5 is a compact stereo direct box designed to accommodate laptop computers, tablets and other consumer audio products when amplifying the signal through a PA system.JD6
The Radial JD6 is a 6-channel rackmount direct box designed for keyboards in studio and live touring where optimal signal transfer is required without noise.ProD8
The Radial ProD8 is a high density 8-channel rackmount direct box optimized for professional keyboard rigs where optimizing signal transfer without noise is needed.StageBug SB5W
The Radial SB5-W is a passive stereo direct box designed to fit inside a standard electrical wall box and utilizing a Decora wall plate cover.
- ACTIVE DI
The Radial Firefly is a class-A direct box that combines a 12AX7 tube drive with transformer isolation to deliver spectacular warmth and character.J48
The Radial J48 is a 48 volt powered active direct box that delivers studio quality performance while eliminating hum and buzz caused by ground loops.JDX 48
The Radial JDX 48 is a guitar amp DI that captures the sound of the amplifier and speaker to deliver the tone of a 4x12 half-stack without the need of a microphone.USB-Pro
The Radial USB-Pro is a high-resolution DI box that converts sound files from a laptop and seamlessly transfers them to a pair of balanced audio outs.JDV MK5
The Radial JDV is a class-A direct box with a unique zero negative-feedback circuit that delivers unmatched signal purity for the most demanding recordings.J48 STEREO
The Radial J48 Stereo is a high performance active direct box with extra headroom and advanced grounding for professional touring and studio recording.PZ-DI
The Radial PZ-DI is a unique direct box that is specifically designed for acoustic and orchestral instruments.JPC
The Radial JPC is an active stereo DI with transformer isolated inputs to eliminate noise that is common with computers and consumer audio devices.Headload
The Headload is a combination load box and attenuator that is capable of handling up to 130 watts RMS of continuous power and peaks of 180 watts.PRO48
The Radial Pro48 is a high performance active direct box that is ideally suited for bass and acoustic guitars to deliver clarity without distortion or artifact.StageDirect
The Radial StageDirect is a state-of-the-art active direct box designed for musicians who require extra control when they are on stage.J33
The Radial J33 is a combination stereo phono preamp and direct box designed to interface turntables to professional audio systems.Headload Prodigy
The Headload Prodigy is a combination load box and DI that lets you perform or record at low volume with maximum tone.StageBug SB-1
The Radial SB-1 is an ultra-compact active direct box designed for acoustic guitar and bass that fits inside a guitar case!StageBug SB-4
The Radial StageBug SB-4 is a compact active direct box that has been optimized for use with piezo transducers.BT-Pro
BT-Pro™ is a Bluetooth® DI designed to capture the wireless transmission from a Bluetooth® device and convert the signal to a balanced line for use in a PA.JDX Direct-Drive
The Radial JDX Direct-Drive™ is a unique and powerful device that simulates the sound of a guitar amplifier.4-Play
The Radial 4-Play™ is a multi-channel direct box that has been specifically developed for multi-instrumentalists to enable them to quickly change instruments on stage.
The Radial X-Amp is a dual output class-A active Reamper that lets you take a pre-recorded track and send it through amps and pedals without noise.Reamp JCR
The Radial Reamp JCR is a high-performance passive Reamper that lets you take a pre-recorded track and send it through a guitar amp or pedal chain without noise.ProRMP
The Radial ProRMP is a passive Reamper that lets you take a pre-recorded track and send it through a guitar amp or pedal chain without noise.X-Amp 500 Series
The Radial X-Amp is a 500 series class-A active Reamper with isolated outputs that lets you send a pre-recorded track to two amps and re-record the new sound.Reamp KIT
The Reamp Kit combines a Radial J48 direct box for recording with a Radial X-Amp for Reamping amps & pedals to enhance the tone of your recorded tracks.SGI
The Radial SGI Studio Guitar Interface class-A line driver with load correction lets you send a guitar signal beyond 100 meters via balanced cable without noise.JD7
The Radial JD7 Injector is a class-A guitar distro/splitter with built-in Radial DI and Reamp that can drive up to seven amps or pedal chains simultaneously.JX44
The Radial JX44 Air Control is a wireless signal manager for concert stage that lets you remotely control 4 guitar inputs and 6 amp outputs at once.SGI-44
The Radial SGI-44 guitar interface is a balanced signal extender designed to send the signal from a wireless receiver to the pedalboard and back to the stage amp.
JS2 / JS3
The Radial JS2 and JS3 are high performance passive microphone splitters that lets you feed mixing consoles without signal degradation or noise caused by ground loops.PRO-MS2
The Radial ProMS2 is a high performance mic splitter that accepts a balanced microphone signal and sends it to three outputs simultaneously. As a passive device, there is no need for power.OX8
The Radial OX8 is an 8-channel rack mounted microphone splitter that lets you feed two mixing consoles without signal degradation or noise caused by ground loops.LX8
The Radial LX8 is an 8-channel rack mounted line level splitter that lets you feed two audio systems without signal degradation or noise caused by ground loops.JD7
The Radial JD7 Injector is a class-A guitar distro/splitter with built-in Radial DI and Reamp that can drive up to seven amps or pedal chains simultaneously.JX44
The Radial JX44 Air Control is a wireless signal manager for concert stage that lets you remotely control 4 guitar inputs and 6 amp outputs at once.mPress
The Radial mPress is a modular press box that can be expanded as needed to feed a community-sized press gallery or distribute audio for an international event.Exo-Pod
The Radial Exo-Pod is a passive broadcast splitter that can take the balanced line output from a mixing console and distribute the signal to 14 hand-held recorders, video cameras or wireless receivers.Catapult
The Radial Catapult is a 4-channel audio snake that lets you send analog or AES digital audio signals over standard Cat 5 or Cat 6 shielded twisted pair cable.LX-2
The Radial LX-2™ is a passive balanced line level audio splitter that allows you to easily send an audio signal to two different destinations at once without noise.LX-3
The Radial LX-3™ is a high-performance balanced line-level splitter designed to send one audio signal to as many as three destinations at once.
The Radial Twin-Iso is a two channel balanced line-level isolator that eliminates the hum and buzz caused by ground loops that is often encountered in audio systems.J-ISO
The Radial J-ISO & Pro-Iso are full bandwidth stereo interfaces that converts +4dB balanced line level signals to an unbalanced consumer level output.Pro-ISO
The Radial J-ISO & Pro-Iso are full bandwidth stereo interfaces that converts +4dB balanced line level signals to an unbalanced consumer level output.J+4
The Radial J+4 is a -10dB to +4dB stereo preamp that lets you boost a low output unbalanced signal and interface it with a balanced professional audio system.JPC
The Radial JPC is an active stereo direct box with transformer isolated inputs to eliminate noise that is common with computers and consumer audio devices.McBoost
The Radial McBoost™ is a high performance microphone signal booster designed to elevate the output of a typical dynamic microphone for greater transient response.SGI
The Radial SGI Studio Guitar Interface class-A line driver with load correction lets you send a guitar signal beyond 100 meters via balanced cable without noise.SGI-44
The Radial SGI-44 guitar interface is a balanced signal extender designed to send the signal from a wireless receiver to the pedalboard and back to the stage amp.STAGEBUG SB-6
The Radial StageBug SB-6 is a high performance 2-channel passive audio isolator designed to accommodate both balanced and unbalanced signals.STAGEBUG SB-7
The Radial StageBug SB-7 Earmuff Headphone Silencer lets you turn off one side of your headphones to stop the bleed.STAGEBUG SB-15
The Radial Stage Bug SB-15 High Performance Signal Buffer lets you drive guitar pedals without added noise and also powers 15V Tonebone pedals.ICECUBE IC-1
The Radial IceCube IC-1 is a balanced line level isolator designed to quickly eliminate hum and buzz problems in an audio system by simply inserting it into the signal path.DECODER
Decoder is a microphone preamp and Mid/Side stereo matrix that allows the user to easily create M/S recordings without having to re-configure a recording consoleSpace Heater
The Radial Space Heater is a single space 8-channel tube overdrive that can be used as a stereo summing mixer or as multi-channel studio distortion.Twinline
The Radial Twinline is a unique device that enables a guitarist to share effects pedals between two amps when using the amplifiers' built-in (rear-panel) effects loops.MR5
The Radial MR5 is a MIDI signal translator that allows you to use a MIDI controller to drive the JX44, JX42 and other Radial products that use the JR5 footswitch.
Radial studio products simplify the work-flow without affecting the signal quality to ensure creativity is not hampered during production.MC3
The Radial MC3 monitor controller is a 'straight wire' passive switcher that lets you control two sets of monitors, sub woofer and feed two sets of headphones.Gold Digger
The Gold Digger is a 4-channel mic selector that enables the engineer to quickly compare the sound of four different microphones while sharing the same preamp.Cherry Picker
The Radial Cherry Picker is a unique tool that simplifies the process of selecting the best preamp for use with a given microphone.
Guitar / Amplifier
Whether switching guitars on stage or amps in the studio, Radial offers a complete range of switchers from simple ABYs all the way up!JD7
The Radial JD7 Injector is a class-A guitar distro/splitter with built-in Radial DI and Reamp that can drive up to seven amps or pedal chains simultaneously.JX-42
The JX-42 is a compact guitar selector that lets you instantly switch between four guitars and two amps on stage.JX62
The Radial JX62 is a guitar and amp switcher designed for both wired and wireless guitars in a live concert touring environment.jx44
The Radial JX44 Air Control is a wireless signal manager for concert stage that lets you remotely control 4 guitar inputs and 6 amp outputs at once.JR5
The JR5 is a remote footswitch that lets you select guitars, amps or effects when used with the JX44 and JX42.JR2
The JR2 is a dual function remote footswitch that lets you switch or mute outputs, depending on the Radial device that is connected.BIGSHOT ABY
The Radial BigShot ABY is a true-bypass ABY switcher that toggles or combines two guitar amplifiers in phase and without hum & buzz caused by ground loops.BigShot I/O
The Radial Bigshot I/O is a true-bypass instrument selector that lets you switch between two sources and balance the signal level between them.BigShot EFX
The Radial BigShot EFX is a true-bypass effects loop switcher that lets you turn on or off two pedal-chains and take them out of the signal path when not in use.BigShot SW2
The Radial BigShot SW2 is a dual output remote control with choice of latching or impulse settings to control two amplifiers or effects.Twinline
The Radial Twinline is a unique device that enables a guitarist to share effects pedals between two amps when using the amplifiers' built-in (rear-panel) effects loops.
Radial addresses the fast paced world of live touring with a range of switchers for backing tracks, wireless systems and mixers.Relay Xo
Radial Relay Xo is a 1-in, 2-out switcher for balanced audio used with mic or line level sources as talkback and communication router.SW4
The Radial SW4 is a four channel balanced audio switcher designed for wireless systems, mixing consoles and digital guitar processors.SW8
The Radial SW8 is a backing track switcher that automatically switches between two playback systems to prevent disaster during a live performance.HotShot DM-1
The Radial HotShot DM-1 is a combination mic mute and switch that enables the artist to communicate to band members and techs via momentary footswitch.HotShot ABi
The Radial HotShot AB1 is an XLR balanced input selector that can instantly toggle between two input sources to one output via a latching footswitch.HotShot ABo
The Radial HotShot ABo is an XLR balanced output selector that can instantly toggle one input between two output destinations via a latching footswitch.JR2
The JR2 is a dual function remote footswitch that lets you switch or mute outputs, depending on the Radial device that is connected.JR2-DT
The JR2-DT is a desk-top version of the JR2. It features two top-mounted activator switches to control AB and Mute functions.BigShot SW2
The Radial BigShot SW2 is a dual output remote control with choice of latching or impulse settings to control two amplifiers or effects.
The Radial Phazer is an analog phase alignment tool that lets you combine two sources and bring the fundamentals together for a more natural tone.Phazer Bank
The Radial Phazerbank is a 4-channel analogue phase adjustment tool that enables the engineer to effortlessly adjust the phase between two microphones when double mic'ing a single source.PhazeQ
The Radial PhaseQ is 500 series phase alignment tool that lets you combine two microphones and bring them into perfect phase for a more natural tone.EXTC-SA
The Radial EXTC-SA™ is a stand-alone audio interface that lets you incorporate guitar effects into the realm of pro-audio recording.EXTC
The Radial EXTC is a 500 series effects send & receive module that lets you incorporate guitar effects into the realm of pro-audio recording.Tank Driver
The Radial Tank Driver is a wonderfully unique 500 series module that allows you to drive a balanced line level signal through the reverb tank in your Fender Twin amp!Vocoloco
The Voco-Loco is a foot-controlled effects loop that enables the lead vocalist, sax or trumpet player to incorporate guitar effects pedals into the signal path, just like an electric guitarist adds effects for soloing.Trimode
The Trimode tube distortion takes you from slight overdrive to full-on distortion. Think Mesa-Boogie in a pedal and switch instantly from rhythm to lead.Vienna Chorus
The Vienna Chorus is vintage bucket-brigade chorus that delivers old-school analog tone. Dual-mode controls lets you switch from slow to fast choral effects like a Leslie.
- 500 SERIES
Choose between Radial's award-winning racks for ultimate control over your signal path. Compatible with all 500 series modules, Radial racks are equipped with extra features for greater connectivity plus resettble electronic fuses to keep your gear safe!Workhorse
The Radial Workhorse is an 8-slot 500 series power rack with a built-in analog summing mixer, headphone amp and extensive patching capabilities.WR8
The Radial WR-8 is an 8-slot power rack that lets you load up to eight 500 series modules. Can be expanded with the WM8 mixer for full Workhorse capabilities.Powerhouse
The Radial Powerhouse is a 10-slot power rack for 500 series modules designed to provide maximum density for professional studio setups.SIXPACK
The Radial SixPack is a desk-top 6-slot power rack for the popular 500 series, designed to create the ultimate channel strip with 1600 milliamps of available current.Cube
The Radial Cube is a desk-top 3-slot power rack for the popular 500 series, designed to create the ultimate channel strip with 500 milliamps of available current.PowerStrip
The Radial Powerstrip is a 3-slot power rack for the popular 500 series, designed to create the ultimate channel strip with 500 milliamps of available current.
Preamps & EQs
Radial gives you a choice between tube and solid state preamps to suit your most demanding recording needs. Compliment them with choice of induction coil or discrete class-A equalizers to add creative soul, sparkle or fat bottom end.POWERPRE
The Radial PowerPre is a 500 series 100% discrete mic preamp with Accustate input control for low noise and transformer coupled output for added warmth.JDV-PRE
The Radial JDV-Pre is a 500 series class-A instrument preamp with variable load for magnetic, piezo and active sources and high-pass filter to eliminate resonance.PowerTube
The Radial Powertube is 500 series 100% discrete class-A preamp with high voltage 12AX7 tube gain stage and transformer coupled input for vintage character.Premax
The Radial PreMax is a 500 series channel strip tha combines a state-of-the-art preamp with a 3-band EQ for easy signal manipulation in post production and recording.Q3
The Radial Q3 is a 500 series induction coil EQ that brings the character and excitement of old-school vintage EQ to your recordings with over 1700 EQ curves.Phaze-Q
The Radial PhaseQ is 500 series phase alignment tool that lets you combine two microphones and bring them into perfect phase for a more natural tone.Twin-Servo
The Radial Jensen Twin-Servo & 500 series preamplifier is an updated version of what may well be the most spectacular preamp ever made.PreComp
The Radial PreComp is a 500 series channel strip that combines a state-of the-art preamp with a full-function VCA compressor for dynamic control over the signal.Q4
The Radial Q4 is a 500 series state-variable, 100% discrete class-A parametric EQ that brings character and warmth to your recordings with minimal artifact
Effects & Routing
The 500 series is all about creative use of signal processing. Radial opens the door with compressors, signal routers, cross-over filters, effects interfaces, phase alignment tools and amp simulators. Finally… amazing tools that let your imagination run wild!EXTC
The Radial EXTC is a 500 series effects send & receive module that lets you incorporate guitar effects into the realm of pro-audio recording.Shuttle
The Radial Shuttle is a 500 series patch and insert panel that lets you bring balanced and unbalanced signals in and out a 500 series power rack.Komit
The Radial Komit is a 500 series one-knob compressor-limiter designed to get great results instantly and add crunch and distortion for unque effects.X-Amp
The Radial X-Amp is a 500 series class-A active Reamper with isolated outputs that lets you send a pre-recorded track to two amps and re-record the new sound.ChainDrive
The Radial ChainDrive is a 500 series signal distribution amplifier that lets you send balanced or unbalanced signals to four outputs and control them independently.Tank Driver
A unique module that lets you to drive a balanced line level signal through the reverb tank in your Fender Twin! Drive spring reverbs of all types and deliver the long trailing shimmering effect that is only possible with a true spring.JDX-500
The Radial JDX Reactor is 500 series guitar amplifier interface that lets you capture the tone of a guitar amp and cabinet without a microphone.Submix
The Radial SubMix is a 500 series mixer that lets you combine 4 instruments such as keyboards or effects into a single audio channel via front panel controls.Tossover
The Radial Tossover is a 500 series frequency divider that lets you separate and process low and high frequencies separately via fully variable controls and slopes.
- CABLES & SNAKES
If you don't see the question you had in mind here, feel free to enter in the form provided along with your email address so we may send the reply directly to you. Thank's for your participation!
What is the Workhorse?
The Workhorse is a rack device that holds eight 500 series modules. These can be used individually or in series to create custom channel strips and unique signal paths. The on-board 8x2 summing mixer allows the engineer to mix directly from the modules and send the left-right output to a recording system, PA and headphones.
Who is it designed for?
Both the recording engineer and the producer will benefit. The engineer will enjoy the ability to create unique signal paths by mixing and matching various modules to create new sounds. The producer will enjoy the fact that he could create a unique signature. Both will enjoy the ease of use and exceptionally clean signal path.
Where will the Workhorse be used?
Because of the modularity, the applications are truly without limit. In the recording studio, the Workhorse enables the engineer to quickly add or remove modules to suit a particular song or passage. For mastering, the engineer can select specific modules to suit ones personal preference. In the field, the engineer could set up stereo, quad, or a multitude of channels by combining two or more Workhorses together.
Would a guitarist benefit from having a Workhorse?
Absolutely! In the studio, the Workhorse can be combined with modules like the Radial JDV instrument preamp, X-Amp Reamper and JDX speaker emulator to create all kinds of musical textures. On the road, the guitarist could create unique audio paths for acoustic and electric guitars.
What makes the Workhorse special?
The fact that you can customize your audio system to meet specific demands and then mix the outputs without having to integrate additional outside gear makes the Workhorse invaluable. And being able to use a host of available modules means that you do not have to pay for expensive power supplies each time; only the signal generating device. This means you get high quality for less money.
Why has this not been done before?
In a way, it has. The Workhorse’s modular concept actually originated from recording consoles. Engineers liked the sound of certain modules but may not have liked the way the console worked. By pulling the modules out of the old desks and putting them into a simple rack-housing, the concept was born. We simply brought back the mixing aspect to better suit today’s recording environment.
How do you patch modules in?
As with any audio system, you should mute or turn off the system before patching to avoid any harmful transients. Modules slide into the Workhorse effortlessly and are then held into place with the top and bottom retainer screws. The signal is then routed from one module to another or sent to the summing mixer.
When would you use the link function?
This is usually reserved for stereo signal paths where you would like both channels to work exactly in the same fashion. Compressing the output of a stereo mix is a good example. Modules like the Radial Komit are equipped to manage stereo signals with the link function. When engaged, the ‘odd numbered’ module’s knobs will control the even numbered module in a master-slave configuration.
What is the ‘feed’ function used for?
This lets you feed the audio from one module into the next one without having to use external cables. So for instance, you could have a preamp going into an EQ, feeding a compressor. You could then simultaneously tap the signal from each module using the XLR output, or audition the summed output via the master mix buss.
Can I use old API Lunchbox modules with the Workhorse?
Yes, the Workhorse will work just like a standard Lunchbox with older modules. To take full advance of the bussing capabilities built in the Workhorse all you do is add an XLR to D-Sub cable and connect it to the summing mixer d-sub connector.
Why is Radial not a VPR Alliance Member?
The membership asks that we send modules to API to make sure our work correctly. It also suggests that modules should be not be sold for under $700-US. Although we respect API, their excellent engineering, and the legacy that they maintain, we feel our engineering team is more than capable of producing high quality products that will meet or exceed the very best equipment in the world. As for price, we plan to offer products at several price points and therefore do not wish to be limited on this matter. If we sell a direct box for $200, and turn it into a 500 series module, we cannot see charging an extra $500 for it.
What is a Virtual Ground Mix Buss?
A ‘Virtual Ground (or Earth) Mix Buss’ is a well liked approach used to create a mixer that is both efficient and noise free. It was popularized by recording mixer console pioneers such as Neve and SSL and has become the format of choice for analogue recording.
What makes one console sound different from another?
The ‘sound’ of a console is mostly attributed to the EQ section. For instance, some folks like the sound of British consoles and the famous British EQ. More expensive consoles employ transformers in their signal path. The transformer will also impart a certain signature. The Jensen transformer is very clean, natural and warm sounding.
How would you rate the sound of the Workhorse?
The Workhorse has no EQ, no effects busses and is very compact. This makes it very quiet and natural sounding. The module you select will pretty much generate the sound, not the Workhorse.
Why are most summing mixers really expensive?
This may be due to the brand equity or maybe because they have expensive transformers on every channel. Some companies can charge more because they are well admired.
In a pinch, can I use the headphone out as another stereo sound source?
Yes. But be careful not to overload the receiving device! There is a lot of signal level coming out of those jacks so you will want to start with the volume set very low and increase as needed.
Some headphones need more power. How does the Workhorse deal with the problem?
Higher impedance headphones (200 ohms) require more power to drive than lower impedance phones (8 ohms). We addressed te problem by introducing a super loud headphone amp.
Can Phantom Power hurt ribbon mics?
There is some truth to this. You should always turn off the phantom power when it is not required. Older ribbon mics are particularly sensitive to phantom and can harm them if the polarity is not correct. But today, this is less of a problem since pretty much all manufacturers follow the AES standard.
Why did you use an external power supply?
For several reasons: First: power supplies generate noise. For years large console manufacturers have always put the power supply outside. By keeping it away, there is less opportunity for induced noise. Second: the power supply is the number-1 electronic point of failure in electronic devices (after user error and connector/switch issues). Should a problem occur, the power supply can be replaced by the user without having to return the Workhorse and have it serviced. Third: the Workhorse is so jammed with electronics, there was simply no space left inside!
Is it true that some 500 series rack do not have enough power?
The API spec calls for 130mA of current on each rail. This is normally plenty for most modules. There are however some companies that employ tubes or for whatever reason are more power hungry. This may be the reason that this problem has surfaced. The Workhorse employs a pooled supply with 1200mA that you can use however you wish. So if you have two modules that need 200mA each, you still have 800mA to supply the rest. Keep in mind most modules require on average about 45mA of current.
Can I use the summing mixer via the 25pin DSub along with modules at the same time?
Yes. The inputs will simply combine together. If you only wish to work with the signal going into the D-Sub, you woudl simply turn down the levels on the modules that are plugges into the rack.
Will the power supply in the rack affect the tone of a module?
No and yes. When a manufacturer produces a module, they will regulate the incoming power so that the circuit gets what it needs to do the job. So if you give a module extra power, it will simply ignore it. Where the tone may suffer has to do with shortage of power. This can starve the circuit which may increase distortion and resulting tone.
Some manufacturers claim that their power supplies sound better than others. Is this possible?
There is no question that if you have more available power, you will have more headroom. This generally results in less distortion. However, given the fact that most 500 series modules work within the framework of +/-16V and about 130 milliamps, so long as the power supply is clean and regulated, they should all sound about the same.
If I have a module in a slot, can I feed it two sources at the same time using the XLR and the TRS inputs?
Yes. So long as the two inputs are the same relative level, they will simply combine. Keep in mind that this can introduce more noise as each signal path will be combined.
If I have a module in a slot, can I use the XLR and the TRS outputs at the same time?
Yes. In most cases the output from a 500 series module is line level. This will simply act like a mult in a studio patchbay.
Can I simultaneously route the summed output from the Workhorse mixer back into two modules?
Yes, but you must limit the number of summed channels to six in order to leave two available for further processing. This will avoid a feedback loop.
Does the FEED function work with all 500 series modules?
Yes. The FEED function connects the XLR output from one slot to the XLR input on the next. The module does not have to be made by Radial to work.
Will the link switch on the Workhorse allow me to create a stereo link with a 3rd party 500 series module that doesn't have a link function?
No. If the manufacture of the module hasn't built a link feature into the module itself then the link switch on the Workhorse will not be active.